Babysense2 + Secure710


Two premium Oricom products in one Value Pack

Because you can’t watch over your baby around the clock, sleep with greater peace of mind while Babysense2 monitors the breathing movement rate of your sleeping baby.

Should these breathing movements fall below a certain rate or not be detected, Babysense2 will alert you audibly and visually.

The Babysene2 Value Pack combines the peace of mind of the Babysense2 Infant Breathing Movement Monitor with the quality video monitoring of the Secure710.

Babysense2 is intended for use as an Infant Apnoea Alarm.


Out of stock

Where to buy
SKU: BS2SC710 Categories: ,
Redesigned compact styling with the same proven technology and performance as the original Babysense2.

  • Babysense2 is included as a medical device on the Australian Register of Therapeutic Goods (ARTG No. 97479)
  • Continually monitors the breathing movement rate of your baby
  • An audible alarm is activated if your baby’s breathing movement slows to a rate of less than 10 breaths per minute or cannot be detected for more than 20 seconds
  • The control unit connects to sensor pads placed under your baby’s mattress
  • Battery operated

Secure710 Key Features:

  • 2.4″ colour LCD display
  • Parent Talk Back
  • 2 x Digital Zoom
  • Infrared camera for night vision
  • Nursery room temperature sensor and alerts
  • Multi-camera capable – connects to up to four cameras.
  • Additional cameras can be purchased separately

Babysense2 is intended for use as an Infant Apnoea Alarm. ALWAYS READ THE LABEL AND USER GUIDE, USE ONLY AS DIRECTED.

Alarm when Breathing Slows or Stops 2 x Sensor Pads 5 Soothing Lullabies Room Temperature Sensor Parent Talk Back SC870 Parent Baby Friendly Night Vision Generic Multi Camera Capability

Download Spec Sheet

Download Babysense2 User Guide
Download SC710 User Guide

FAQ’s for Oricom Babysense2

Q. Is it a medical device?
A. Babysense2 is included as a medical device on the Australian Register of Therapeutic goods (ARTG No. 97479).

Q. Is it simple to set up and easy to use?
A. Yes, extremely simple to set up and operate, however we strongly recommend the user guide instructions be followed and functionality regularly tested.

Q. Is it portable?
A. Yes, it uses 4xAA Alkaline batteries (not supplied) so you can move it easily.

Q. I’ve read that the babysense2 monitor runs on batteries. How long (on average) will the batteries normally last before needing to change them?
A. The babysense2 is Powered by 4 x AA, 1.5-volt Alkaline batteries (not supplied). Power consumption is approximately 1mA. Battery life is approximately 6 months using high quality alkaline batteries.

Q. Can it be used in cribs, bassinets, travel cot?
A. Yes, as long as the base is rigid and a suitable mattress is used and you must ensure that excess cords are secured under the mattress out of reach of baby or other infants. Modifications may be required to the bassinet for sensor pad wiring access and controller unit placement. For further advice please consult an Oricom Representative.

Q. How many sensor pads does it have?
A. It comes with two highly sensitive sensor pads that cover the area of a standard sized crib or cot.

Q. What age groups is it suitable for?
A. It is suitable for healthy infants up to one year (12months) of age (it cannot be used for children or adults).

Q. If I have twins, can I use with both babies in one cot?
A. No you will need to have babies in separate cots, each with its own Babysense2 monitor.

Q. Lights on Control unit do not illuminate when turned ON?
A. Batteries are not inserted incorrectly or may be flat. Check batteries are inserted in the Control unit observing the correct polarity. Control unit requires 4 x AA 1.5V Alkaline batteries (not supplied).

Q. Low battery voltage warning (red light) on the Control Unit is flashing?
A. Batteries are low, replace all 4 batteries.

Q. Alarm goes off after a few hours
A. The mattress is not touching the sensor pads.
The mattress is raised (there is an object near the sensor pads).
Two sensor pads are connected but the baby is not yet crawling.
Only one sensor pad is connected and the baby has crawled off the sensor pad.
The mattress does not enable adequate transfer of baby movement – The compositions of some cot mattresses may not conduct vibrations associated with babies breathing movement and may not be suitable with Babaysense2.
Do not use Babysense2 with a memory foam mattress.
Make sure that the mattress and sensor pads are touching.
Make sure that there are no objects next to the sensor pads.
Connect sensor pads as per the user manual. If baby is not yet able to crawl, use only one sensor pad – and make sure sensor is placed underneath baby’s location in bed to ensure greater relative sensitivity.
Place a sheet of plywood (not supplied) under the sensor pad so that the sensor pad and the mattress will be tightly pressed together.

Q. Delayed alarms while taking the baby out of the bed
A. Performance test is not correct.
Do not conduct performance test by taking the baby out of bed and waiting for the alarm to go off. Kindly conduct performance test according to the performance test instruction in user guide.
The alarm does not go off within 20 seconds when performing the correct performance test
Environmental Influences detected by the sensor pads, such as wind, fan, air-conditioner, toy mobile vibrations.
Perform a test which will detect the source of the movement that the device detects, eg; sources of wind such as air conditioner, an open window or a fan, movements of baby mobile (which can vibrate even if it’s not turned on) walking around the bed area or an intercom placed near the bed with intense transmission levels. Eliminate sources of wind, remove the mobile etc. After neutralizing all environmental interruptions, perform the test again.

Q: Can I use the Babysense2 on my 13-month-old infant?
A: Babysense2 is intended for healthy newborn infants from birth and up to 1 year of age.
Babysense is set to recognize a defined breathing movement rate of infants within this age group (the alarm sounds if breathing stops for 20 seconds or if the breathing rate slows to below 10 breaths per minute).

Q. Can I use Babysense2 if my infant needs constant medical supervision?
A. No. You should contact your GP or medical specialist and seek their advice on what alternative suitable methods of monitoring your infant are available.

Q. Why is it recommended that only one pad be used in a bassinette?
A: The Babysense2 detects the movement produced by a baby’s breathing. A newborn, being smaller, may not have as much movement than a 3 or 4-month-old baby, and when two sensor pads are connected it does reduce the sensitivity of the pads, a little, no problem for an older baby but maybe a little more difficult to detect the movement for a new born baby. This is why it is always best to follow the instructions in the user guide including performing a regular (daily) test of the monitor.
Babysense2 is intended for use as an Infant Apnoea Alarm.

FAQ’s for Oricom SC710

Q: My SC710 keeps showing ‘Out of Range’ or the picture is ‘frozen’. How do I fix this?
A: The most likely reason for receiving the out of range alert, frozen picture or limited range on your baby monitor is frequency congestion. If this is the cause, resetting your monitor will avoid busy channels.
1) Turn both Camera and Parent units off and remove the battery in the parent unit. Leave unplugged for 1 minute.
2) If you have Wi-Fi in the home, make it busy by streaming a video on YouTube or similar.
3) Turn the camera back on wait for 30 seconds.
4) Ensure the antenna on both the parent unit and camera unit is in the vertical position.
5) Plug the battery into the parent unit and turn on.

If the display is still showing “Out of Range” please relink the units as instructed in the user guide. When relinking it is best to keep the camera and parent units close together (within 1m) and keep clear of all other electronic devices including mobile phones, tablets or computers.

Q: How do I register a new camera unit?
1) Switch on the parent unit.
2) Press and hold the camera button on the parent unit until appears on the screen.
3) After registration icon appears, press the arrow up or arrow down button to select the camera channel [C1] or [C2] or [C3] or [C4] that you want the camera unit to pair with.
4) Press and release the menu key (magnifying glass) to confirm camera number registration.
5) Switch the camera unit ON. Press the pair key once (at the back of the camera unit).
6) If registration is successful, camera video appears on parent unit screen.
7) If the registration time is expired or registration fails, [Out of Range] appears on the LCD.

Q: How many cameras can I connect to the one parent unit?
A: The SC710 can connect up to 4 camera units (CU710) to the one parent unit. The original unit is supplied with one camera. Additional cameras can be purchased from our online store or from your local baby store. Note: The SC710 can connect to both CU710 and CU850PT Motorised Pan-tilt camera units.

Q: The amber light stays illuminated on my parent unit even when finished charging.
A: That’s ok. The amber light indicates that power is being supplied to the cradle. Even when the battery is fully charged, the amber light will stay on.

Q: I don’t seem to be getting the best possible range from my unit.
A: To get the optimum range from your SC710, extend both the antenna on the camera unit and the antenna on the parent unit vertically, so they point straight up. Keep in mind that doors, walls and electrical equipment can reduce the range of your unit.

Q: When I put my monitor on ‘scan’, the cameras continue to say, “out of range”, but they work singularly. What is the problem?
A: Ensure your cameras are selected to be in the scan sequence. You can check this by pressing the camera button to display each camera. Each camera number should have a tick mark against it. If it has a cross, simply press the up or down volume key to change it to a tick. This will include that camera number in the scan sequence.

Q: My parent unit screen goes blank after 10 seconds.
A: This may be as a result of the VOX (sound detection) setting. The screen will turn off when no sound is detected, but will reactivate when the sound threshold reaches a set level, or when any button on the parent unit is pressed. The VOX setting can be activated or deactivated via the menu key.

Q: How long should my battery last?
A: Depending on the usage of the monitor, the parent unit will work for up to 8 hours on a brand new, fully charged battery with the VOX feature turned on. When the battery level becomes low, the amber power LED will flash slowly. At this point you will need to return the parent unit to the charger. Over time your battery life may become shorter. When the battery life is no longer suitable, we suggest you replace your battery. These can be purchased from our online store.

Q: My screen is showing in black and white, not colour. What has happened?
A: The camera has high-intensity infrared LEDs for picking up clear images in the dark. When the built in photo sensor detects a low level of ambient light, the LEDs will automatically activate and the screen on the parent unit will display in black and white.

Q: What are the lullabies on this unit?
A: 1- Twinkle Twinkle Little Star
2- Silent Night
3- Minuet in G Major
4- Londonderry Air 4
5- Blue Danube

Q: My Monitor is telling me the temperature is 3 to 4 degrees higher than the room temperature?
A: The sensor on the back of the baby unit should be positioned as far away from the monitor as possible in a horizontal direction. There should be some airflow around the sensor to allow the temperature of the room to be measured the tolerance of the displayed temperature is + or -2 degrees C

Q: On my SC710 screen I am seeing HI/LO flashing indicator, but, I have temperature warnings Off. Is this normal?
A: Even with the temperature warning alarm turned off, the indicator icon for Low or High temp will still flash, Hi will flash when the temperature is over 30 degrees C, Lo will flash when the temp is below 16 degrees C, however the audible alarm will not indicate with temp warning off.
This is simply an additional feature that gives an indication of hi/lo temperature, without the alarm function.

Q: What is the Scan Mode?
A: When multiple cameras are registered to the parent unit, the scan mode will cycle through each camera, displaying the image for 10 seconds. The audio for the associated image will be played, i.e. if camera 1 image is displayed, you will receive the audio for camera 1. The parent unit will continue to scan through all cameras connected. If you need to view a camera for more than 10 seconds, deactivate the scan mode.

Q: Why is there an X next to my camera?
A: the camera has been temporally disabled.
To resolve this press & release the camera button until it shows the camera that is showing the X.
Press & release the arrow up button, this will then show a tick & reconnect.


  • 2B0081

    Cot Bracket Babysense2

  • 2B0013


  • 2B0015


  • 2B0008

    Power Adaptor SC910, SC710, SC850, SC703, SC705, SC700

  • 2B0001

    Belt Clip SC710

  • CU850PT

    CU850 Additional Camera Unit for SC850

  • 2B0077

    Battery to suit SC720, SC710, SC705 & SC703

  • 2B0043

    Charge Cradle SC710, SC705 and SC703

  • CU710

    CU710 Additional Camera Unit for SC710



Find the answers to your questions here


Be the first to know about our new products