Babysense2 + Secure320

$329.00

Exclusive to Baby Bunting

Two effective Oricom products in one Value Pack

Because you can’t watch over your baby around the clock, sleep with greater peace of mind while Babysense2 monitors the breathing movement rate of your sleeping baby.

Should these breathing movements fall below a certain rate or not be detected, Babysense2 will alert you audibly and visually.

The Babysene2 Value Pack combines the peace of mind of the Babysense2 Infant Breathing Movement Monitor with the quality audio monitoring of the Secure320.

Babysense2 is intended for use as an Infant Apnoea Alarm. ALWAYS READ THE LABEL AND USER GUIDE, USE ONLY AS DIRECTED.

Out of stock

Where to buy
SKU: BS2SC320 Categories: ,
Redesigned compact styling with the same proven technology and performance as the original Babysense2.

  • Babysense2 is included as a medical device on the Australian Register of Therapeutic Goods (ARTG No. 97479)
  • Continually monitors the breathing movement rate of your baby
  • An audible alarm is activated if your baby’s breathing movement slows to a rate of less than 10 breaths per minute or cannot be detected for more than 20 seconds
  • The control unit connects to sensor pads placed under your baby’s mattress
  • Battery operated

The Babysene2 Value Pack combines the peace of mind of the Babysense2 Infant Breathing Movement Monitor with the quality audio monitoring of the Secure320.

  • Reassuring adjustable night light
  • Hi-definition sound (DECT)
  • Sound sensitive light display
  • Mute function
  • Fully adjustable digital volume control
  • Out of range/ low battery warning
  • Rechargeable batteries (supplied) in-use time up to 16 hours
Breathing Movement Monitor Alarm when Breathing Slows or Stops 2 x Sensor Pads Parent Talk Back SC870 Parent Adjustable Night Light Sound sensitive light display

Download Spec Sheet

Download Babysense2 User Guide
Download SC320 User Guide

FAQ’s for Oricom Babysense2

Q. Is it a medical device?
A. Babysense2 is included as a medical device on the Australian Register of Therapeutic goods (ARTG No. 97479).

Q. Is it simple to set up and easy to use?
A. Yes, extremely simple to set up and operate, however we strongly recommend the user guide instructions be followed and functionality regularly tested.

Q. Is it portable?
A. Yes, it uses 4xAA Alkaline batteries (not supplied) so you can move it easily.

Q. I’ve read that the babysense2 monitor runs on batteries. How long (on average) will the batteries normally last before needing to change them?
A. The babysense2 is Powered by 4 x AA, 1.5-volt Alkaline batteries (not supplied). Power consumption is approximately 1mA. Battery life is approximately 6 months using high quality alkaline batteries.

Q. Can it be used in cribs, bassinets, travel cot?
A. Yes, as long as the base is rigid and a suitable mattress is used and you must ensure that excess cords are secured under the mattress out of reach of baby or other infants. Modifications may be required to the bassinet for sensor pad wiring access and controller unit placement. For further advice please consult an Oricom Representative.

Q. How many sensor pads does it have?
A. It comes with two highly sensitive sensor pads that cover the area of a standard sized crib or cot.

Q. What age groups is it suitable for?
A. It is suitable for healthy infants up to one year (12months) of age (it cannot be used for children or adults).

Q. If I have twins, can I use with both babies in one cot?
A. No you will need to have babies in separate cots, each with its own Babysense2 monitor.

Q. Lights on Control unit do not illuminate when turned ON?
A. Batteries are not inserted incorrectly or may be flat. Check batteries are inserted in the Control unit observing the correct polarity. Control unit requires 4 x AA 1.5V Alkaline batteries (not supplied).

Q. Low battery voltage warning (red light) on the Control Unit is flashing?
A. Batteries are low, replace all 4 batteries.

Q. Alarm goes off after a few hours
A. The mattress is not touching the sensor pads.
The mattress is raised (there is an object near the sensor pads).
Two sensor pads are connected but the baby is not yet crawling.
Only one sensor pad is connected and the baby has crawled off the sensor pad.
The mattress does not enable adequate transfer of baby movement – The compositions of some cot mattresses may not conduct vibrations associated with babies breathing movement and may not be suitable with Babaysense2.
Do not use Babysense2 with a memory foam mattress.
Make sure that the mattress and sensor pads are touching.
Make sure that there are no objects next to the sensor pads.
Connect sensor pads as per the user manual. If baby is not yet able to crawl, use only one sensor pad – and make sure sensor is placed underneath baby’s location in bed to ensure greater relative sensitivity.
Place a sheet of plywood (not supplied) under the sensor pad so that the sensor pad and the mattress will be tightly pressed together.

Q. Delayed alarms while taking the baby out of the bed
A. Performance test is not correct.
Do not conduct performance test by taking the baby out of bed and waiting for the alarm to go off. Kindly conduct performance test according to the performance test instruction in user guide.
The alarm does not go off within 20 seconds when performing the correct performance test
Environmental Influences detected by the sensor pads, such as wind, fan, air-conditioner, toy mobile vibrations.
Perform a test which will detect the source of the movement that the device detects, eg; sources of wind such as air conditioner, an open window or a fan, movements of baby mobile (which can vibrate even if it’s not turned on) walking around the bed area or an intercom placed near the bed with intense transmission levels. Eliminate sources of wind, remove the mobile etc. After neutralizing all environmental interruptions, perform the test again.

Q: Can I use the Babysense2 on my 13-month-old infant?
A: Babysense2 is intended for healthy newborn infants from birth and up to 1 year of age.
Babysense is set to recognize a defined breathing movement rate of infants within this age group (the alarm sounds if breathing stops for 20 seconds or if the breathing rate slows to below 10 breaths per minute).

Q. Can I use Babysense2 if my infant needs constant medical supervision?
A. No. You should contact your GP or medical specialist and seek their advice on what alternative suitable methods of monitoring your infant are available.

Q. Why is it recommended that only one pad be used in a bassinette?
A: The Babysense2 detects the movement produced by a baby’s breathing. A newborn, being smaller, may not have as much movement than a 3 or 4-month-old baby, and when two sensor pads are connected it does reduce the sensitivity of the pads, a little, no problem for an older baby but maybe a little more difficult to detect the movement for a new born baby. This is why it is always best to follow the instructions in the user guide including performing a regular (daily) test of the monitor.
Babysense2 is intended for use as an Infant Apnoea Alarm.
ALWAYS READ THE LABEL AND USER GUIDE, USE ONLY AS DIRECTED.

FAQ’s for Oricom SC320

Q: Parent Unit is continually beeping?
A: Please see page 17 (User Guide) for the list of tones the Parent unit makes. The Parent unit will beep for a number of reasons:

1) The link has been lost between your units, see page 11 (User Guide). Check that the Baby Unit Link indicator is illuminated. If not, please ensure that the power adaptor is still connected and if this still does not switch on, please test into a different electrical socket.
2) The crying alert is switched on, see page 14 (User Guide).
3) The batteries are low, see pages 9-10 (User Guide).
4) The Find button has been pressed on the Baby unit, see page 16 (User Guide).

If the Parent unit still beeps after checking the above, please try switching the Baby unit off at the power. Ensure the Parent unit is clean by wiping with a damp cloth. If the problem persists call the Oricom Customer Support for advice.

Q: The battery is low on the Parent Unit?
A: Put the Parent unit back on charge.
Place the Parent unit back on charge as frequently as possible or ideally leave it on charge to ensure the batteries remain charged.
To fully charge the batteries, the Parent unit should be on charge for approximately 24 hours if switched on or 16 hours if switched off to reach maximum charge.
To speed up the charging process turn the Parent unit off when charging if it is not being used.

Q: The Parent Unit remains silent or very quiet?
A: You may have set the volume too low, see page 14 to increase the volume.

Q: I can hear the unit making a high-pitched noise?
A: The units might be too close to each other. The volume setting might be too high, see page 14 (User Guide).

Q: The talk back feature is not working as it should be?
A: Check that the Units are correctly linked.

NEED SUPPORT?

Find the answers to your questions here

KEEP IN TOUCH

Be the first to know about our new products